hilscher netHOST NHST-T100 User Manua Download Page 63

Page: 63 / 75

Technical data

63/75

NHST-T100-DP/CO/DN

Parameter

Value

Ethernet Interface (X2)

Transmission rate

100 MBit/s

10 MBit/s

Interface type

100 BASE-TX, isolated

Half duplex/Full duplex

supported (at 100 MBit/s)

Auto-Negotiation

supported

Auto-Crossover

supported

Connector

2 * RJ45

PROFIBUS DP Interface
(X3) NHST-T100-DP

Transmission rate

9.6 kBit/s,
19.2 kBit/s,
31.25 kBit/s,
45.45 kBit/s,
93.75 kBit/s,
187.5 kBit/s,
500 kBit/s,
1.5 MBit/s,
3 MBit/s,
6 MBit/s,
12 MBit/s

Interface type

RS 485, optically isolated

Connector

SubD female, 9-pin

CANopen Interface (X3)
NHST-T100-CO

Transmission rate

10 kBit/s,
20 kBit/s,
50 kBit/s,
100 kBit/s,
125 kBit/s,
250 kBit/s,
500 kBit/s,
800 kBit/s,
1 MBit/s

Interface type

ISO 11898, optically isolated

Connector

SubD male, 9-pin

DeviceNet Interface (X3)
NHST-T100-DN

Transmission rate

125 kBit/s,
250 kBit/s,
500 kBit/s

Interface type

ISO 11898, optically isolated

Connector

COMBICON, 5-pin

Table 49: Technical data netHOST for Fieldbus systems (Part 2)

Summary of Contents for netHOST NHST-T100












































































Search results

Summary of Contents for netHOST NHST-T100

Reviews:

Related manuals for netHOST NHST-T100

Brands by name

Popular brands

hilscher netHOST NHST-T100, User Manua

Search results

Summary of Contents for netHOST NHST-T100

Reviews:

Related manuals for netHOST NHST-T100

Brands by name

Popular brands