hilscher netHOST NHST-T100 User Manua Download Page 29

Page: 29 / 75

Requirements

29/75

Requirements for using the SYCON.net configuration software

For installing and operating the SYCON.net configuration software, you
need the following:

PC with 1 GHz processor or higher

Windows

XP SP3, Windows

Vista (32 bit) SP2, Windows

7 (32 bit)

SP1, Windows

7 (64 bit) SP1, Windows

8 (32 bit) or Windows

8 (64

bit)

Administrator privilege required for installation

Internet Explorer 5.5 or higher

Free disk space: min. 400 MByte

DVD ROM drive

RAM: min. 512 MByte, recommended 1024 MByte

Graphic resolution: min. 1024 x 768 pixel

Keyboard and Mouse

Ethernet interface

Note:

If the project file is saved and opened again or it is used on another
PC, the system requirements need to match. Particularly the DTMs
need to be installed on the used PC.

Restrictions

Touch screen is not supported.

Summary of Contents for netHOST NHST-T100












































































Search results

Summary of Contents for netHOST NHST-T100

Reviews:

Related manuals for netHOST NHST-T100

Brands by name

Popular brands

hilscher netHOST NHST-T100, User Manua

Search results

Summary of Contents for netHOST NHST-T100

Reviews:

Related manuals for netHOST NHST-T100

Brands by name

Popular brands