manualshive.com logo in svg

HIKVISION DS-M5504HNI Series, User Manual

Share
Download
HIKVISION DS-M5504HNI Series User Manual Download Page 16

Mobile Network Video Recorder User Manual 

15 

Positive pole ignition switch 

 

Figure 1. 4

 

Connection of Positive Pole Ignition Switch 

 

Ignition switch is connected to the positive pole of DC+12/24V of vehicle batteries. Please make sure that the connection is 

correct, and then perform the following steps: 

Steps:

 

1.

 

Connect the “DC IN +” of mobile NVR to the positive pole of vehicle batteries, jumping over the switch of normal 

vehicle power. 

2.

 

Connect the “DC IN -” and “KEY -” of mobile NVR to the negative pole of vehicle batteries. 

3.

 

Connect the “KEY +” of mobile NVR to the vehicle ignition switch. 

 

The normal vehicle power refers to the main power of the vehicle power supply system. After the vehicle is off, the 

normal vehicle power still provides direct-current source for the other devices inside and generally a main switch is 

used to turn on/off it. 

Negative pole ignition switch 

 

Figure 1. 5

 

Connection of Negative Pole Ignition Switch 

 

Ignition switch is connected to the negative pole of DC+12/24V of vehicle batteries. Please make sure that the connection is 

Summary of Contents for DS-M5504HNI Series















































































Reviews:

No comments

Brands by name

Popular brands

Load more brands