9
English
23. Disconnect the hose and take out any nails left in
the magazine after use.
Disconnect tool from air before doing tool maintenance,
cleaning a jammed fastener, leaving work area, moving
tool to another location, or after use. It is very dangerous
for a nail to be
fi
red by mistake.
24. When removing a nail which has become stuck,
make sure to
fi
rst of all disconnect the hose and
release compressed air.
When removing a nail which has become stuck in the
nail outlet,
fi
rst of all make sure to disconnect the hose
and release compressed air inside the power tool.
Accidental
fi
ring of the nail could be very dangerous.
25. A female plug (air socket) should not be used in
the body.
If a female plug is installed in the body, the compressed
air sometimes can not be drawn when the hose is
disconnected so avoid this.
The tool and air supply hose must have a hose coupling
such that all pressure is removed from the tool when the
coupling joint is disconnected.
26. While using a tool, the operator shall adopt a
suitable but ergonomic posture.
Maintain secure footing and avoid awkward or o
ff
-
balanced postures.
27. If the operator experiences symptoms such as
persistent or recurring discomfort, pain, throbbing,
aching, tingling, numbness, burning sensation, or
sti
ff
ness, do not ignore these warning signs.
The operator shall consult a quali
fi
ed health
professional regarding overall activities.
28. Long time continuous and repetitive work may
lead to muscular-skeletal disorders.
Do not keep working with a same posture or by applying
excessive force for a long time.
And take some rest regularly and especially when you
feel tired.
29. Slips, trips and falls are major causes of workplace
injury.
Be aware of slippery surfaces caused by use of the tool
and also of trip hazards caused by the airline hose.
30.
Proceed with additional care in unfamiliar
surroundings.
Hidden hazards may exist, such as electricity or other
utility lines.
31. Make sure there are no electrical cables, gas pipes
etc. that could cause a hazard if damaged by use
of the tool.
32. Risk assessment should include dust created by
the use of the tool and the potential for disturbing
existing dust.
33. Direct the exhaust so as to minimize disturbance
of dust in a dust
fi
lled environment.
34. Where dust or exhaust hazards are created, the
priority shall be to control them at the point of
emission.
35. Information to conduct a risk assessment of
these hazards and implementation of appropriate
controls is essential.
36. Exposure to vibration can cause disabling damage
to the nerves and blood supply of the hands and
arms.
37.
Wear warm clothing when working in cold
conditions, keep your hands warm and dry.
38. If you experience numbness, tingling, pain or
whitening of the skin in your
fi
ngers or hands,
seek medical advice from a quali
fi
ed occupational
health professional regarding overall activities.
39. Operate and maintain the tool as recommended
in these instructions, to prevent an unnecessary
increase in vibration levels.
40. Hold the tool with a light, but safe, grip because
the risk from vibration is generally greater when
the grip force is higher.
41. When attaching and detaching the nose cap,
disconnect the hose.
When attaching the accessory nose cap to the tip of
the push lever and when detaching it, make sure to
disconnect the hose beforehand. It is very dangerous
for a nail to be
fi
red by mistake.
SPECIFICATIONS
Type of power
Piston reciprocating
Air pressure (Gauge)
4.9 – 8.3 bar (70 – 120 psi)
Applicable nails
ref. Fig.
Numbers of loadable nails
100 nails (1 strip)
Size
254 mm (L) × 233 mm (H) × 60 mm (W) (10” × 9-3/16” × 2-3/8”)
Weight
1.0 kg (2.2 lbs)
Nail-feeding method
Spring type
Hose (inside dia.)
6 mm (1/4”)
0000Book̲NT50AE2(S).indb 9
0000Book̲NT50AE2(S).indb 9
2019/08/02 16:25:01
2019/08/02 16:25:01
