HES HS1102S User Manual Download Page 5 | Manualshive

Page: 5 / 35

background image

Hwang Sun Enterprise Co., Ltd.

Edition 2012/06

4

1)

Do not try to remove the molten adhesive on the skin.

2)

Immerse the affected area into cold water until the adhesive is cooled down.

3)

Do not try to remove the cooing adhesive from the skin.

4)

Wrap the wound with clean and wet clothing. If the condition of injury is very serious,
please keep the patient’s body temperature in normal temperature, and send the patient
to the hospital immediately.

«
...
3
4
5
6
7
...
»

Summary of Contents for HS1102S




































Reviews:

No comments

Related manuals for HS1102S

Brand: Wavetek Pages: 74

Brand: Fairchild Pages: 16

Brand: R.M. Young Pages: 10

Brand: Federal Signal Corporation Pages: 4

Brand: FASTERHOLT Pages: 96

Brand: iHealth Pages: 8

Brand: Balanced Body Pages: 4

Brand: Balanced Body Pages: 2

Reformer Trapeze Combination

Brand: Balanced Body Pages: 164

Brand: Wacker Neuson Pages: 50

Brand: Balanced Body Pages: 37

Brand: YOKOGAWA Pages: 75

Brand: FARM-MAXX Pages: 35

Brand: Goobay Pages: 6

Brand: Life Fitness Pages: 8

Brand: Moticon Pages: 24

MERLIN N Series

Brand: Meheen Pages: 24

Brand: Williams Sound Pages: 32

Brands by name

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Popular brands

Load more brands