HES HS1102S User Manual Download Page 10 | Manualshive

Page: 10 / 35

background image

Hwang Sun Enterprise Co., Ltd.

Edition 2012/06

9

2) Electronic temperature controller

This temperature controller is mainly used to control temperature of dispensing nozzle and
heating hose. There are signs on control panel to mark which one is for dispensing nozzle or
heating hose.
Temperature setting is by turning the knob. (5

℃

per graduation) The heating indicator on left

side is on while heating.

3) MIAN POWER AWITCH

SWITCH TO “ON” POSITION, THE INDICATOR
ON CONTROL PANEL WILL BE ON.

4) START/STOP SWITCH OF MOTOR

Press “START” button (green) to turn on the motor
when the temperature of the hot melt tank has already
reached the setting value. If temperature has not
reached yet, the motor cannot be started.

«
...
8
9
10
11
12
...
»

Summary of Contents for HS1102S




































Reviews:

No comments

Related manuals for HS1102S

Brand: C.M.O Pages: 10

Brand: NEC Pages: 44

medialon Showmaster Go

Brand: 7th Sense Pages: 9

Brand: ZIGBEE Pages: 4

Brand: CAIRE Pages: 38

Brand: Caframo Pages: 72

Brand: p-light Pages: 28

Brand: NANLUX Pages: 39

Brand: Parker Pages: 39

Brand: Parker Pages: 64

Brand: Parker Pages: 40

Matrx Digital MDM

Brand: Parker Pages: 20

Brand: Parker Pages: 52

Brand: Yamaha Pages: 45

Brand: Calibre Fitness Pages: 11

Avisa Line XL04

Brand: FHF Pages: 2

Brand: Joerns Healthcare Pages: 106

Brand: Mindray Pages: 295

Brands by name

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Popular brands

Load more brands