manualshive.com logo in svg

Helwett Packard HP 8512A, Manual, Page: 65 / 108

Share
Download
Helwett Packard HP 8512A Manual Download Page 65

The replaceable parts lists consist of illustrations and tables. Use the illustrations to identify the part to

be ordered; use the tables to determine the ordering information. 

Each table is arranged in 

numerical order by reference designator. The reference designator keys the part listed to the illustra-

tion. The first part number listed is HP’s part number and may differ from the manufacturer’s part

number. The check digit serves as an error check of the part number and should be used when ordering
a part. Quantity refers to the total number of that part in the instrument. The description is a brief written
description of the part and may be used for ordering purposes. Manufacturers code is a five digit
number assigned to each manufacturer (identified in Table 6-l). The manufacturer part number may or
may not be the same as the HP part number.

The replaceable parts of ports 1 and 2 of the HP 8514B are identified in Figure 6-6.

The replaceable parts of ports 1 and 2 of the 

 are identified in Figure 6-10. Additional center

conductor and outer nut replacement information is in 

Service Note 

For information concerning the repair of 3.5 mm rear panel connectors, refer to the 

Test Set Trouble-

shooting 

section of the 

 Service Manual 

or 

Service Note 

Table 6-1. Manufacturer Codes and Reference Designations

MANUFACTURER’S CODES

Code

Manufacturer Name Address

Zip

Code

00000

00853
24546
28480

56289

ANY SATISFACTORY SUPPLIER
SANGAMO ELEC CO   CAROLINA DIV
CORNING GLASS WORKS (BRADFORD) BRADFORD

HEWLETT-PACKARD CO CORPORATE HQ PALO ALTO
SPRAGUE ELECTRIC COMPANY NORTH ADAMS

REFERENCE DESIGNATIONS

SC 29671

PA 16701
CA 94304

MA 01247

A 

assembly

AT 

attenuator

B fan

C capacitor
E miscellaneous electrical part
F fuse
FL filter

J electrical connector, jack

MP miscellaneous part

resistor

T transformer
W cable, wire
X socket

More comprehensive tables of manufacturer codes, reference designators, and abbreviations are
behind the REPLACEABLE PARTS tab of the HP8510B Service Manual.

6-2 Replaceable Parts

HP 

 Test Sets

Summary of Contents for HP 8512A













































































































Reviews:

No comments