manualshive.com logo in svg

Helwett Packard HP 8512A, Manual, Page: 108 / 108

Share
Download
Helwett Packard HP 8512A Manual Download Page 108

REGIONAL SALES AND SUPPORT OFFICES

For information relating to Sales or Support of Hewlett-Packard products first contact your local Hewlett-Packard 
listed in the white pages of your telephone directory. If none is listed locally, contact one of the addresses listed below
to obtain the address or phone number of the Hewlett-Packard Sales or Support office nearest you.

ASIA

Hewlett-Packard Asia Ltd.

47/F, 26 Harbour Road,
Wanchai, HONG KONG
G.P.O. Box 863, Hong Kong
Tel: (852) 58330833
Telex: 76793 HPA HX
Cable: 

 TD

AUSTRALASIA

Hewlett-Packard Australia Ltd.

31-41 Joseph Street
BLACKBURN, Victoria 3130
Australia
Tel: (61) 895-2895
Telex: 31-024
Cable: HEWPARD Melbourne

CANADA

Hewlett-Packard (Canada) Ltd.
6877 

 Drive

 Ontario 

 1 M8

Tel: (416) 678-9430
Telex: 069-8644

JAPAN

Yokogawa-Hewlett-Packard Ltd.
29-21 Takaido-Higashi, 3 Chome
Suginami-ku TOKYO 168
Tel: 03 (331) 6111
Telex: 232-2024 YHPTOK

MEDITERRANEAN AND
MIDDLE EAST

Hewlett-Packard S.A.
Mediterranean and Middle East

Operations
Atrina Centre
32 Kifissias Avenue
Paradissos-Amarousion, ATHENS
Greece
Tel: (30) 682 88 11
Telex: 21-6588 HPAT GR
Cable: HEWPACKSA Athens

February, 1986

BENELUX   SCANDINAVIA

Hewlett-Packard S.A.
Uilenstede 475
P.O. Box 999
NL-1183 AG AMSTELVEEN

The Netherlands
Tel: (31) 

 77 71

Telex: 18 919 hpner nl

SOUTH   EAST EUROPE,
AFRICA

Hewlett-Packard S.A.

7, rue du Bois-du-Lan
CH-1217 

 2, Geneva

Switzerland
Tel: (41) 

 12 12

Telex: 27835 hmea
Cable: HEWPACKSA Geneve

FRANCE

Hewlett-Packard France

 d’activites du Bois Briard

2, avenue du Lac
91040 EVRY Cedex
Tel: 1 

 83 83

Telex: 6923 15F

GERMAN FEDERAL
REPUBLIC

Hewlett-Packard 
Hewlett-Packard-Strasse
Postfach 1641
D-6380 BAD HOMBURG

West Germany
Tel: 06172/400-O
Telex: 410 844 hpbhg

ITALY

Hewlett-Packard ltaliana 

Via G. Di Vittorio 9
l-20063 CERNUSCO SUL

(Milano)
Tel: 

 36 91

Telex: 334632

UNITED KINGDOM

Hewlett-Packard Ltd.
King Street Lane

Winnersh, 

Berkshire 

 5AR

Tel: 

 47 74

Telex: 847178

EASTERNUSA

Hewlett-Packard Co.

4 Choke Cherry Road
ROCKVILLE, MD 20850
Tel: (301) 670-4300

MIDWESTERN USA

Hewlett-Packard Co.
5201 

 Drive

ROLLING MEADOWS, IL 60008

Tel: (312) 255-9800

SOUTHERNUSA

Hewlett-Packard Co.

2000 South Park Place

P.O. Box 105005

ATLANTA, GA 30348
Tel: (404) 955-1500

WESTERN USA

Hewlett-Packard Co.

5161 Lankershim Blvd.

P.O. Box 3919
NO. HOLLYWOOD, CA 91609

Tel: (818) 506-3700

OTHER INTERNATIONAL
AREAS

Hewlett-Packard Co.
Intercontinental Headquarters

3495 Deer Creek Road

PALO ALTO, CA 94304

Tel: (415) 857-l 501
Telex: 034-8300
Cable: 

Summary of Contents for HP 8512A













































































































Reviews:

No comments