manualshive.com logo in svg

Helwett Packard HP 8512A, Manual, Page: 64 / 108

Share
Download
Helwett Packard HP 8512A Manual Download Page 64

Section 6. Replaceable Parts

This section contains information for ordering parts. Exchange Assemblies Available describes how to
order assemblies which are available on an exchange basis. Table 6-1 is a list of manufacturers (by
code number) and reference designations.

HP8514B replaceable parts are identified by Table 6-2 and Figures 6-l through 6-7.

 replaceable parts are identified by Table 6-3 and Figures 6-3, 6-4 and 6-8 through 6-10.

 

 

The items below are replaceable on a rebuilt exchange basis at a cost saving. They are not 

repairable. Defective assemblies must be returned for credit to realize the cost savings. Thus,
assemblies required for spare parts stock should be ordered by the new assembly part number which
is included in the replaceable parts list of this section. See the parts list for the orderable part numbers.

l 

A2 IF multiplexer board assembly

. A3

 summing amplifier board assembly

l 

A4

 board assembly

l 

A5 attenuator/switch driver assembly*

l 

A6 coupler

l 

A7 bias tee*

. A8 coupler*

. A9

l 

A10

l 

All

l 

Al2

l 

Al3

l 

Al4

bias tee*
sampler assembly (input bl)
sampler assembly (input b2)
sampler assembly (input al)
sampler assembly (input 
VTO/driver assembly

l 

Al5

 Al6

l 

Al7

 Al8

regulator board assembly
step attenuator*
step attenuator*
switch/splitter*

l 

HP 8514B only

HP 

 Test 

Replaceable Parts 6-1

Summary of Contents for HP 8512A













































































































Reviews:

No comments