Helwett Packard HP 8512A Manual Download Page 41

Page: 41 / 108

Handle only at Static Safe

Work Stations

The assemblies handled in this procedure are VERY SENSITIVE TO

DAMAGE BY STATIC ELECTRICITY.

PLEASE PAY ATTENTION TO THESE INSTRUCTIONS! Expensive assem-
blies are destroyed EVERY DAY because anti-static precautions are not

taken seriously.

WEAR AN ANTI-STATIC WRIST STRAP THAT IS CONNECTED TO EARTH
GROUND. If you ground the strap to the instrument chassis, make sure

the instrument is plugged in, otherwise you are not connected to earth

ground. An ungrounded instrument can not provide sufficient protection,

and can even build up its own static charge.

Table 5-4. Required Tools and Supplies

Tools Used On HP Part Number

Anti-static wrist strap all components 9300-1257 (Medium)

9300-0970 (Large)

Anti-static mat

9300-0797

Small pozidriv (1 pt.)

8710-0899

Medium pozidriv (2 pt.)

8710-0900

torque wrench, 72 lb-in coupler MTB 100 72 LB-IN

6” torque wrench, 10 lb-in

Clip lead capacitors purchase locally

6” nut driver connector repair

torque wrench, 25 lb-in connector repair 8710-1581

Microwave Connector Care Manual all connectors 08510-90064

3.5 mm connector

3.5 mm connectors 1250-1862

Connector cleaning

all connectors 92193Z

1 OOR 20 watt resistor capacitor removal

1. Order from Mountz Company, 1080 North 11th Street, San Jose, CA 95112.
2. Contains male and female gage and calibration block. These gages come with

mm HP 8510calibration kit.

If you own a calibration kit, refer to

kit manual for information on gaging and cleaning the connector.

3. Refer to the

Microwave

Connector

Care

Manual for cleaning instructions. Note, early versions of this manual

recommend cotton swabs, however, the new foam swabs provided in the connector cleaning kit should always
be used instead.

5-8 Test

Troubleshooting HP

Test

Summary of Contents for HP 8512A













































































































Search results

Summary of Contents for HP 8512A

Reviews:

Helwett Packard HP 8512A, Manual, Page: 41 / 108

Search results

Summary of Contents for HP 8512A

Reviews: