Helmer iBX020 Service Maintenance Manual Download Page 48

Page: 48 / 55

360203-1/B

Parts & Schematics

12 .6

Rear Exterior

The amperage sum of the kiosk and printer connected to the iBX020 AC output power receptacle cannot exceed 2 Amps. If the

sum is greater than 2 Amps, the printer must be connected to an alternate power source.

When using 100V system, the amperage draw of the kiosk and printer connected to the iBX020 AC output power receptacle

cannot exceed 1.25 Amps.

Label

Description

Part Number /

Service Kit Number

Removable rear panel

Call for part number

iBX020 iC

USB

Call for part number

iBX020 RJ45 Ethernet port for connection to BloodTrack® kiosk

Call for part number

Remote alarm contacts

Call for part number

AC output power cord receptacle (optional use with BloodTrack®

kiosk; non-fused; must limit)

Call for part number

iBX020 power entry / line filter

Call for part number

Summary of Contents for iBX020
























































Search results

Summary of Contents for iBX020

Reviews:

Related manuals for iBX020

Brands by name

Popular brands

Helmer iBX020, Service Maintenance Manual

Search results

Summary of Contents for iBX020

Reviews:

Related manuals for iBX020

Brands by name

Popular brands