manualshive.com logo in svg

HELI CPC 20, Manual

Share
Download
HELI CPC 20 Manual Download Page 95

starting circuit and the starter can not be started.

(2) Light switch

The switch is put out to 1st step to turn on the front and rear width indicators and 

to 2nd step to turn on the front big lamp.

(3) Signaling for left turning

Pull  back  the  turning  lamp  switch  and  the  left  turning  lamp  in  the  front 

combination lamp lights up.

(4) Signaling for right turning

Push  froward  the  turning  lamp  switch  and  the  right  turning  lamp  in  the  front 

combination lamp lights up.

(5) Signaling for braking

When the emergency braking is required, press the braking pedal and the braking 

lamp in rear combination lamp (red) lights up.

(6) Signaling for the reverse of the truck

When the reverse of the truck is required, position the change-over lever to the 

reverse step, the reverse lamp lights up and the back buzzer sounds.

(7) Displaying for charging signal

When  right  turning  the  key  switch  to  1st  step,  the  charging  indicator  lights  up 

and after the engine starts, it goes out automatically. If it lights up during the engine 

running,  this  indicates  the  charging  circuit  goes  out  of  order.  In  this  time  it  is 

necessary to stop the truck to find reasons.

(8) Displaying for oil pressure signal

When right turning the key switch to 1st step, the oil pressure indicator lights up 

and after the engine starts, it goes out automatically. If it lights up during the engine 

running, this indicates the lubrication goes out of order. In this case, it is necessary to 

stop the truck to find reasons.

(9) Fuel meter

It indicates the volume of fuel oil in fuel system.

-93-

Summary of Contents for CPC 20



































































































Reviews:

No comments

Brands by name

Popular brands

Load more brands