manualshive.com logo in svg

HELI CPC 20, Manual

Share
Download
HELI CPC 20 Manual Download Page 14

1.2.1 Fuel tank

The  fuel  tank  is  a  welded  construction  integrated  with  the  truck  frame.  It  is 

located  on  the  left  side  of  the  truck  frame  and  has  a  capacity  of  52l  for  2-3.8  ton 

trucks. The fuel volume sensor is installed on the tank cover to detect the fuel level. 

1.2.2 Fuel volume sensor

Fig. 1-2 Fuel volume sensor

The sensor is designed to convert the remaining amount of fuel into voltage. (See 

Fig.1-2) The sliding type resistor made of alloy steel wire is linked with float. As the 

float moves up and down, resistance is changed. With electro-magnetic fuel meter, the 

remaining amount of fuel in the fuel tank can be read off the meter panel.

1.2.3 Maintenance

Once  every  100  working  hours,  it  is  required  to  maintain  the  fuel  system 

according to the following methods. Once every 600 working hours, it is required to 

clean the fuel tank.

The highest lever 

Float

The lowest lever

Truck capacity

Float position

1

1/2

0

2-3.8 (

ton)

Resistance (Ω)

55

43

10

-12-

Summary of Contents for CPC 20



































































































Reviews:

No comments

Brands by name

Popular brands

Load more brands