HELI CPC 20 Manual Download Page 53

Page: 53 / 98

seals.

(2) Press the hub bearings into the hub and fit the hub on the knuckle shaft.

(3) Fit a flat washer and tighten a castle nut to a torque of 206-235N.m (21-

24kgm) and loosen it and then tighten it again to a torque of 9.8N.m (1kgm).

(4) To ensure firm installation of the hub, slightly knock at it with a wooden

hammer and in the meantime, rotate the hub for 3-4 turns.

(5) Tighten the castle nut and align one of its notches with a cotter pin hole

drilled in the steering knuckle.

(6) Again slightly knock at the hub with a wooden hammer and in this time,

rotate manually the hub for 3-4 turns to ensure its smooth rotation with a specified

torque of 2.94-7.8N.m (0.3-0.8kgm).

(7) If the torque value necessary to rotate the hub is more than the specified one

above-mentioned, screw out the castle nut for 1/6 turn and measure the torque value

then.

(8) When the torque value measured is up to the specified one, lock the castle nut

-51-

Summary of Contents for CPC 20



































































































Search results

Summary of Contents for CPC 20

Reviews:

Brands by name

Popular brands

HELI CPC 20, Manual

Search results

Summary of Contents for CPC 20

Reviews:

Brands by name

Popular brands