manualshive.com logo in svg

HELI CPC 20, Manual

Share
Download
HELI CPC 20 Manual Download Page 73

lubrication method so as to minimum the clearance of the gear face.

Since the pump body and cover are made of aluminum alloy, they are light and 

rigid.  The  driving  gear  and  driven  gear  are  integrated  with  their  respective  shafts 

which  are  held  in  bushings.  The  bushings  made  of  special  metal  serves  both  as 

bearings for each shaft and as side plates for the gear face. 

At the driving shaft side, an oil seal is press fitted into the pump body to provide 

oil tightness performance. Oil tightness between the pump body and the pump cover is 

secured with a packing with special shape.

9.3 Control Valve & Divider (See Fig.9-1)

The control valve (2 spool type) consists of four valve housings, two spools, one 

relief valve and one flow divider. The four valve housings are assembled together with 

three stud bolts and nuts. The tilt spool valve contains a tilt lock valve.

Fig.9-1 Control valve

Relief valve Lifting spool valve Tilting spool valve

To pressure gauge

To steering unit

Flow divider

To oil tank

To oil pump

-71-

Summary of Contents for CPC 20



































































































Reviews:

No comments

Brands by name

Popular brands

Load more brands