HELI CPC 20 Manual Download Page 33

Page: 33 / 98

4.Hydraulic-powered Transmission & Torque Converter

4.1 General Description

Hydrodynamic transmission type forklift trucks are provided with a drive unit

including a torque converter and a hydraulic transmission (See Fig.4

1). They feature

the following:

(1) With an inching valve, the inching operation can be done under the

conditions that the engine runs at both high and low speeds.

(2) Each of two hydraulic clutches is provided with four pairs of steel plates and

paper friction pieces specially-treated, so as to improve the durability of friction pair.

(3) Both on-way overrun clutches in the torque converter are used to increase the

efficiency for power transmission.

(4) High quality of oil filters is helpful to increasing the life of the torque

converter.

Torque converter

Type

Torque ratio

Set pressure

Charging pump

Type

Flow rate

Transmission

Type

Speed ratio FWD/BWD

Hydraulic clutch

Friction piece O.D.×I.D.×T.

Friction area

Set pressure

Weight of drive unit

Oil amount

Oil type

Three elements, single stage, two phases

0.5-0.68MPa

Inner-mesh gear type

27l/min (2000rpm, 1.5MPa)

Power shifted

1.35/1.35

125×81×2.7mm

71cm

1.1-1.4MPa

165kg

Model SAE 10W engine oil

No.6 Torque converter oil made in China

-31-

Summary of Contents for CPC 20



































































































Search results

Summary of Contents for CPC 20

Reviews:

Brands by name

Popular brands

HELI CPC 20, Manual

Search results

Summary of Contents for CPC 20

Reviews:

Brands by name

Popular brands