manualshive.com logo in svg

HELI CPC 20, Manual

Share
Download
HELI CPC 20 Manual Download Page 39

Fig. 4-5 Inching valve

4.5 Transmission Case

It is used to contain the input shaft, the output shaft, etc. and serve as an oil tank. 

There  is  an  oil  filter  (I)

 

of  150  meshes  in  specification  at  the  bottom  of  the  case  to 

filter  the  oil  from  the  charging  pump. The  oil  filter  (II)

 

for  the  pipeline, the  oil  inlet 

cover and the dip stick are all fixed at the top of the case cover.

4.6 Charging Pump (See Fig.4-6)

The  charging  pump  between  the  torque  converter  and  the  input  shaft  of  the 

transmission  is  a  gear  pump  driven  by  the  turbine  shaft  concluding  a  pair  of  inner-

meshed  gears  for  the  purpose  of  feeding  the  oil  to  the  torque  converter  and  the 

transmission.

(1)Snap ring  
(2) O-ring  
(3) Inching valve rod  
(4) Snap ring  
(5) Spring  
(6) Valve core
(7) Spool  
(8) Valve body  
(9) Spring  
(10) O-ring  
(11) Cover  
(12) Oil seal

-37-

Summary of Contents for CPC 20



































































































Reviews:

No comments

Brands by name

Popular brands

Load more brands