HELI CPC 20 Manual Download Page 87

Page: 87 / 98

(5) Turn the pump body over. Put driving gear(5) and driven gear(6) in the pump

body so that the same teeth may be engaged as they were meshed before disassembly.

(6) With the same procedure as step(4), install bushings(3) and (4) toward the

front cover side.

(7) Install the packing ring(8), (9), (10) and (11) correctly. Be careful not to

overlap the packing at the center.

(8) Install the front cover(7) with the driving gear face covered with tapes to

avoid the lip of the oil seal to be damaged, but do not forget to remove the tapes after

the installation.

(9) Notice to prevent the packing rings(8), (9), (10) and (11) installed in the

step(7) from sliding when turning the pump body over to install the rear cover.

(10) With the same method as in step(7), install another packing rings(8), (9),

(10) and (11).

(11) Install the rear cover(1).

(12) Install the lock washer(13) and bolts(12) and tighten up the bolts with a

+0.26

+0.25

torque of 47

N.m (4.7

kgm).

Check the gear pump for completeness and correctness and then clamp down its

driving shaft with a vice to check the pump to see if it is easy to be rotated. If it is hard

to be rotated, recheck the pump.

Check the gear pump for the assembly and rotation direction before installing it

to the machine.

The followings should be noticed when installing it to the machine:

a) Check the gear pump's portion below the center section for damage and dust.

b) Check the flange surface of the pipeline for damage and dirts.

Install the O-ring in the flange of the pipeline after finishing procedures above.

9.8.4 Trial run

After installing the gear pump in the truck, check it reassembled for specified

performance and do the running-in for it. If the pump’s gears are seized or internal

-85-

Summary of Contents for CPC 20



































































































Search results

Summary of Contents for CPC 20

Reviews:

Brands by name

Popular brands

HELI CPC 20, Manual

Search results

Summary of Contents for CPC 20

Reviews:

Brands by name

Popular brands