manualshive.com logo in svg

HELI CPC 20, Manual

Share
Download
HELI CPC 20 Manual Download Page 36

The way of torque-converting can be used to ensure efficient and smooth work 

of the torque converter.

The torque converter, filled up with the torque converter oil, in the drive unit is 

driven  by  an  engine  through  a  spring  plate  and  flywheel  on  the  engine. A  charging 

pump  is  driven  by  a  driving  gear  which  is  splined  to  the  impeller.  The  oil  for  the 

torque  converter  and  the  transmission  is  supplied  by  the  pump.  The  power  is 

transmitted to the transmission through a turbine shaft splined to the turbine.

4.3 Hydraulic Clutch (See Fig.4-3)

Both hydraulic multipiece clutches of wet type are fixed on the input shaft of the 

transmission.  The  pressure  oil  is  supplied  to  the  forward  or  the  backward  clutch 

through a control valve to achieve the forward or the backward travel of the truck. All 

of gears in the transmission are normally meshed.

Every clutch consists of four (five 3.8t) spacers (24) and four 

friction 

pieces  (25)  assembled  alternately  and  a  piston.  On  the  inner  and  the  outer  circles  of 

the piston are seal rings for sealing the piston. In the neutral, the piston is still and the 

spacers  and  the  friction  pieces  are  disengaged  each  other.  When  shifting,  the  oil 

pressure  acts  on  the  piston  and  the  spacers  and  the  friction  pieces  are  engaged  each 

other to form an integral so that the power from the torque converter is transmitted to 

the forward driving gear (13) or the backward driving gear (4).

The  power  from  the  torque  converter  is  transmitted  to  the  transmission  in 

following order:

Turbine-Input  shaft-Spacer-Friction  piece-Forward  or  backward  driving  gear- 

Output shaft.

(five 3.8t) 

-34-

Summary of Contents for CPC 20



































































































Reviews:

No comments

Brands by name

Popular brands

Load more brands