HELI CPC 20 Manual Download Page 18

Page: 18 / 98

(8) Press the clutch pedal and remove the three spacers.

(9) Adjust the travel of the clutch pedal. (See Fig.2-2)

2.3 Clutch Pedal

The clutch pedal and the brake pedal are fitted on the same bracket. The clutch

pedal is secured on the transmission.

2.4 Adjustment of Clutch Pedal Travel (See Fig.2-2)

(1) Loosen clutch pedal stopper bolt (a).

(2) Using stopper bolt (a) to get a pedal height from the floor of 111mm. Spare

travel is 30-40mm.

(3) Detach the spring at the end of the clutch pedal and loosen the nut (b).

(4) Press the clutch pedal about 30 to 40mm. At this time, pull the release yoke

forward. When resistance is felt, turn spherical nut (b) until it comes into contact with

release yoke and then lock with lock nut (c).

(5) Install the pedal spring properly.

Spare travel

Pedal height 115mm

Stopper bolt (a)

Spherical bolt (b)

Lock nut(c)

Clutch pedal

Fig.2-2 Clutch pedal

-16-

Summary of Contents for CPC 20



































































































Search results

Summary of Contents for CPC 20

Reviews:

Brands by name

Popular brands

HELI CPC 20, Manual

Search results

Summary of Contents for CPC 20

Reviews:

Brands by name

Popular brands