Heise PTE-2 Operation And Maintenance Manual Download Page 66

Page: 66 / 88

SECTION 15 n.

CALIBRATE BASE UNIT CONT.

Documenting Calibration Data Procedure
NOTE: The input jacks for the 10 and 30 volt inputs are the

same input jacks, the accuracy statement for 10 volts is for

values between 0 and 10 volts DC, the accuracy statement for

30 volts DC is for values above 10 volts to 30 volts DC
VOLTAGE JACK INPUT, 0-10 volts
1. Connect the negative lead of the voltage standard to the

black ringed “COM” input jack

2. Connect the positive lead of the voltage standard to the red

ringed “0-33Vdc In” jack

3. Power on a voltage standard capable of delivering up to

10.000v DC and allow it to warm up to its specified accu-

racy as defined by the manufacturer

4. Power on the HHC using either USB or battery power and

allow it warm up to its specified accuracy (5 minutes)

5. Set the voltage standard to 0.000 volts dc

6. With the HHC in measure mode press the Ma/V key repeat-

edly until a voltage reading appears on the display

7. Make note of the voltage standard input voltage and the

voltage value displayed on the HHC display.

8. Verify that displayed voltage is within ±2.0 mV (±0.0020

volt)

9. I ncrease the input voltage setting from the voltage standard

at desired intervals until reaching 10.000 volts.

10. Note input standard voltages and HHC displayed voltages

and calculate error.

11. It is recommended to at minimum verify display voltage at

0.000 and 10.000 volts input.

12. When test is complete, set voltage standard to 0.00 volts

and disconnect the leads from the HHC.

VOLTAGE JACK INPUT, 10-30 volts

1. Connect the negative lead of the voltage standard to the

black ringed “COM” input jack

2. Connect the positive lead of the voltage standard to the red

ringed “0-33Vdc In” jack

3. Power on a voltage standard capable of delivering up to

30.000v DC and allow it to warm up to its specified accu-

racy as defined by the manufacturer

4. Power on the HHC using either USB or battery power and

allow it warm up to its specified accuracy (5 minutes)

5. Set the voltage standard to 10.000 volts dc

6. With the HHC in measure mode press the mA/V key

repeatedly until a voltage reading appears on the display

7. Make note of the voltage standard input voltage and the

voltage value displayed on the HHC display.

8. Verify that displayed voltage is within ±30 mV (±0.03 volt)

9. Increase the input voltage setting from the voltage standard

at desired intervals until reaching 30.000 volts.

10. Note input standard voltages and HHC displayed voltages

and calculate error.

11. It is recommended to at minimum verify display voltage at

10.00 and 30.00 volts input.

Summary of Contents for PTE-2

























































































Search results

Summary of Contents for PTE-2

Reviews:

Related manuals for PTE-2

Brands by name

Popular brands

Heise PTE-2, Operation And Maintenance Manual

Search results

Summary of Contents for PTE-2

Reviews:

Related manuals for PTE-2

Brands by name

Popular brands