manualshive.com logo in svg

Heise PTE-2, Operation And Maintenance Manual

Share
Download
Heise PTE-2 Operation And Maintenance Manual Download Page 30

 28

SECTION 15 c. 

 ENGINEERING UNITS SELECTION

Auto Off Modes

Power Off…
Backlight Off…

Power Off Times

Never
 5 Minutes

15 Minutes

30 Minutes

60 Minutes

Select Ch1 Unit

psi

inH2O

inHg

 kPa

1 of 13 units

Press ENTER

Use DOWN or UP ARROW to highlight “Auto off timer…”

Press ENTER

Use DOWN or UP ARROW to highlight “Power off”…

OR

Use DOWN or UP ARROW to highlight “Backlight off”…

Press ENTER

Use DOWN or UP ARROW to highlight desired time in minutes 

or “Never”

 

Press ENTER

HHC will return to Measurement Mode with values being saved

Select Engineering Units
Press MENU key

Press DOWN or UP ARROW key to highlight “Units…”

Press ENTER

Press DOWN or UP ARROW key to highlight “Select Units”

Press ENTER

Press DOWN or UP ARROW key to highlight “Channel 1 

Module”, “Channel 2 Module” 

Press ENTER

Press DOWN or UP ARROW key to highlight desired engineer-

ing unit

Press Enter to select unit and exit to Measurement Mode. 
Note: The HHC has 99,999 counts of resolution.  The display 

is capable of displaying five digits up to 99,999. Selecting engi-

neering units which approach 99,999 counts of resolution could 

result in the least significant digits to appear unstable. 
Note: Units of measure whose full scale value exceeds 99,999 

will not be available to be selected. 

SECTION 15 b. iii 

 Program Auto Off Timers Cont.

Summary of Contents for PTE-2

























































































Reviews:

No comments

Brands by name

Popular brands

Load more brands