manualshive.com logo in svg

Heise PTE-2, Operation And Maintenance Manual

Share
Download
Heise PTE-2 Operation And Maintenance Manual Download Page 50

 48

If Manual was selected continue below

Press left and RIGHT ARROWs to position cursor beneath 

desired numeric character.
Press UP and DOWN ARROWs to scroll numeric values. 
When desired numeric value is displayed in proper decimal 

position, press LEFT or RIGHT ARROW to move cursor 

beneath the next digit to be programmed. 
Continue until all required digits are populated on the display.
When desired Reference temperature value in selected engi-

neering units is displayed on screen for example 0070.00
Press ENTER to accept
HHC will go back to TC Module MENU and advance to the next 

programmable parameter “Resolution”….
With “resolution…” highlighted press ENTER
Use DOWN or UP ARROW to highlight “1, .1, .01 or Auto”
Note: If selecting “Auto”, the calibrator will adjust the display to 

the greatest significant resolution.
Press ENTER
TC Module programming screen will appear with “Apply” high-

lighted.
If previously programmed settings are acceptable press 

ENTER
HHC will enter Measurement Mode and display temperature as 

programmed. 
 
The HHC is shipped with the latest firmware (application soft-

ware) available at the time of manufacture. When firmware 

updates are released, they will be made available on our web-

site.
The following steps outline the process of updating the HHC’s 

firmware:
1) Install the FDTI USB Driver on the Host PC.
2) Install the HHC Firmware updater on the Host PC.
3) Download the HHC Firmware Image to the Host PC.
4) Connect the HHC to the Host PC.
5) Run the HHC Firmware Updater on the Host PC.
6) Transfer the firmware file

1) Install the FTDI USB Driver on the Host PC:
Before connecting the HHC to your desktop computer, you 

must install the correct USB driver. Installing this driver will 

allow Microsoft Windows to recognize the HHC as a standard 

COM port. Windows will assign the next available COM Port 

Number to the HHC. For example: COM4.
Note: This driver may already be installed on your PC.
This driver is available from a third party, Future Technology 

Devices International, and is also included on the memory stick 

that you received with your HHC.
The internet link to the driver is:
http://www.ftdichip.com/Drivers/CDM/CDM 2.08.30 WHQL 

TC Manual Ref

00000.00

^

Enter to accept

Esc to cancel

SECTION 15 k. 

 THERMOCOUPLE TEMPERATURE  

MEASUREMENT CONT.

SECTION 15 l. 

 FIRMWARE UPDATE

Summary of Contents for PTE-2

























































































Reviews:

No comments

Brands by name

Popular brands

Load more brands