Healy VP1000 Installation, Operation And Maintenance Manual Download Page 1

ARB Approved IOM – Executive Orders VR-201-B and VR-202-B (Wayne Harmony WayneVac Dispenser) 

Page 103 

Healy Systems, Inc. 

                                                        Website: http://www.healysystems.com 

18 Hampshire Drive 

                                                                  Email: [email protected] 

Hudson, New Hampshire 03051 USA 

                                                                              Telephone: 603.882.2472 

ARB Approved Installation, Operation and Maintenance Manual (November 2006)                                    Fax: 603.882.5189 

 

 

 

Healy Systems, Inc. – the innovative leader of Stage II vapor recovery equipment

 

 

WAYNE-DRESSER HARMONY

 SERIES DISPENSER 

RETROFIT for HEALY SYSTEMS, INC.  

MODEL VP1000 

VAPOR RECOVERY ASSIST SYSTEM 

(KIT Z080) 

OUTLINE 

NOTICE: USE THIS PROCEDURE IF CONVERTING A WAYNE-VAC™ VAPOR RECOVERY 

ASSIST SYSTEM TO A HEALY VAPOR RECOVERY ASSIST SYSTEM 

 

See Healy Systems Kit Z078 For Dispensers With Balance Systems 

 

1.  Purpose 

2.   Safety 

3.   Models Covered 

4.   Parts Lists 

5.   Tools Required 

6.   Dispenser Access 

7.   Survey Scope Of Work 

8.   Wayne-VAC Removal 

9.   Installing The Healy VP1000 System   

10.  Connecting Vapor Lines  

11.  Installing The Sealed Nipple Assembly 

12.  Wiring Inside The Electronics Compartment 

13.  Connecting Healy Systems Dispensing Equipment 

14.  VP1000 Theory Of Operation 

15.  Testing The System 

16.  Trouble Shooting The VP1000 

17.  VP1000 Vane & Rotor Service & Replacement Guide 

Start-up / New Installation / Warranty / Annual Testing Form (Rev. 11/06) 

 

Summary of Contents for VP1000





















Reviews: