Harris RMXDIGITAL, Operation & Technical Manual

Page: 43 / 118

Revision C • 10/07
H A R R I S C O R P O R A T I O N
2-27
2 Installation
PIN # PIN #
PIN # PIN # PIN # SIGNAL
SIGNAL
SIGNAL SIGNAL SIGNAL
FUNCTION FUNCTION
FUNCTION FUNCTION FUNCTION
1 L L
L L
LOGIC GR OGIC GR
OGIC GR OGIC GR
OGIC GROUND OUND
OUND OUND
OUND Logic ground
2 T T T T TALK INPUT (-) ALK INPUT (-) ALK INPUT (-) ALK INPUT (-) ALK INPUT (-) Remote Talkback switch input (active low)
3
OFF INPUT (-) OFF INPUT (-)
OFF INPUT (-) OFF INPUT (-) OFF INPUT (-) Remote Off switch input (active low)
4 ENABLE L ENABLE L ENABLE L ENABLE L ENABLE LOGIC INPUT OGIC INPUT OGIC INPUT OGIC INPUT OGIC INPUTS (+) S (+) S (+) S (+) S (+) Jumper to +VDC to enable switch inputs
5
OFF OFF
OFF OFF OFF T
T
T T TALL
ALL
ALL ALL ALLY
Y
Y Y Y Off tally output, N.O. contact
6 T T T T TALL ALL ALL ALL ALLY C Y C Y C Y C Y COMMON OMMON OMMON OMMON OMMON Tally relays common connection, C contact
7 +5 +5
+5 +5
+5 V V
V V
VOL OL
OL OL
OLT L T L
T L T L
T LOGIC SUPPL OGIC SUPPL
OGIC SUPPL OGIC SUPPL
OGIC SUPPLY Y
Y Y
Y 5 volt source for Cough and Talkback Tallies
8 C C C C COUGH INPUT (-) OUGH INPUT (-) OUGH INPUT (-) OUGH INPUT (-) OUGH INPUT (-) Remote Cough switch input (active low)
9
ON INPUT (-) ON INPUT (-)
ON INPUT (-) ON INPUT (-) ON INPUT (-) Remote On switch input (active low)
10 +5 +5 +5 +5 +5 V V V V VOL OL OL OL OLT L T L T L T L T LOGIC SUPPL OGIC SUPPL OGIC SUPPL OGIC SUPPL OGIC SUPPLY Y Y Y Y 5 volt source to enable switches
11
ON ON
ON ON ON T
T
T T TALL
ALL
ALL ALL ALLY
Y
Y Y Y On tally output, N.O. contact
12 +5 +5 +5 +5 +5 V V V V VOL OL OL OL OLT L T L T L T L T LOGIC SUPPL OGIC SUPPL OGIC SUPPL OGIC SUPPL OGIC SUPPLY Y Y Y Y 5 volt source for switch tallies
Notes: +VDC is b5 and +40 VDC.
Outputs can switch voltages up to +60 VDC at 350 mA total
B B
B B
Bold old
old old
old indicates connections used in this example.
ASSIGNABLE LOGIC I/O CONNECTOR SIGNAL TABLE
(wire insertion end view)
MIC REMOTE CONTROL CONNECTION EXAMPLE
This example shows a mic remote control panel connected to an Assignable Logic I/O connector, using the
default logic settings. Information on binding the logic to the mic audio input and the channel strip session
settings for microphones are covered in chapter 4, RMX digital Server and in Appendix A, VMCC.
1 2 3 4 5 6
7 8 9 10 11 12
ASSIGNABLE
LOGIC CONNECTOR
99-1197 or 99-1198
MIC CONTROL PANEL
SIGNAL PIN PIN SIGNAL
BLK
WHT
RED
GRN
BRN
BLU
ORG
YEL
Logic GND
Off Tally
On Tally
Power Supply
Off Switch
On Switch
Cough Switch
Talkback Switch
1
2
3
4
5
6
7
8
1
5
11
7
3
9
8
2
6
12
4
10
Logic Ground
Off Tally
On Tally
+5 VDC Supply
Off Switch (-)
On Switch (-)
Cough Switch (-)
Talk Switch (-)
Tally Common
+5 VDC supply
Enable Logic Inputs (+)
+5 VDC Supply
PARTS LIST
Cable: Belden 9421 or equiv.
8-pin MOD IV Housing: 14-486 (Tyco-AMP 87631-4)
12-pin MOD IV housing: 14-490 (Tyco-AMP 87922-2)
MOD IV contacts: 15-938-1 (Tyco-AMP 102128-1)
KSU CARD
Mic control Panel
(99-1198) connected to
Assignable Logic I/O D
Mic (with preamp)
connected to
analog Input D
TALK
BACK
OFF
ON
COUGH
EXAMPLE OF A MIC & CONTROL PANEL USING
INPUT D ON THE KSU CARD