Harris RMXDIGITAL, Operation & Technical Manual

Page: 58 / 118

Revision C • 10/07
H A R R I S C O R P O R A T I O N
3-12
3 Operation
lower priority buses are assigned on more To
Record Telco channels.
As in creating the foldback mix, the bus prior-
ity order changes when any To Record Telco has
AUTO F/B On. Since multiple channels could have
AUTO F/B turned On, it is easiest to record call-
ers with AUTO F/B turned off on all Telco chan-
nels or only set one Telco as the To Record Telco.
To summarize, here are the two Telco recording
priorities and what happens in each condition:
AUTO F/B is off on all To Record Telco channels:
The Base Mix source is Offline. If it is not as-
signed, then the program buses are used in order;
PGM 1, PGM 2, PGM 3, PGM 4.
If Offline is the base mix source, then it doesn’t
matter whether the channels are On or Off, all To
Record Telco channels will be recorded (as shown
in the adjacent illustration).
If a program bus is the base mix source, then
the To Record Telco channel must be On to record
the caller. If a To Record Telco channel is Off, then
that caller is NOT being recorded.
AUTO F/B is lit on at least one To Record Telco:
In this mode, the base mix source follows the
On/Off state of all of the To Record Telcos with
Auto F/B lit. When all of the Telcos with Auto F/B
lit are On, then PGM 1 is the primary base mix (if
it is not assigned then PGM 2, then PGM 3, then
PGM 4, then Offline is used).
When any To Record Telco channel, with Auto
F/B lit is turned Off, then Offline is the base mix
source and if it’s not assigned, no callers will be
recorded. This is summarized below.
Recording Functions with Auto F/B
On—on any To Record Telco Channel
LEFT CHANNEL
RIGHT
CHANNEL
NOT
RECORDED
All Telco channels which are assigned
TO RECORD by the session file.
All channels assigned to the Base Mix
bus, including those Telco modules
that are not assigned
TO RECORD .
Any channel NOT assigned to the Base
Mix bus.
TELCO RECORD OUTPUT SUMMARY
Note: Offline feeds from non-Telco channels are
always pre-switch. They were set to Pre- or Post-
Fader during console setup. The Telco channels’
Offline bus feeds can be separately set for Pre- or
Post-Fader by session file settings.
The Telco Record bus should be in the CR moni-
tor selector list and may be assigned to a monitor
select button so it can easily be monitored since
this is the other method to verify the correct Telco
channels and talent signals are being recorded.
Base Mix Source
(feeds the right
channel of the
Telco Record
Output)
Channel On/Off
status does not
affect the Telco
Record Outputs
Base mix source when
this channel is Off
since AUTO F/B is lit.
Telco 1 feeds
the left channel of the
Telco Record Output,
regardless of channel
On/Off status.
The Telco 1 channel
On/Off status changes
the base mix source
between Offline (when
Off ) and PGM 1 (when
On).
Base mix source when
this channel is On
since Auto F/B is lit.
Since Auto F/B is un-lit,
this channel does not
affect the base mix source.
This channel will NOT be
recorded because the channel
is Off (which unassigns it from
the PGM 1 base mix, which is
the record base mix, since
Telco 1 is On).
If Telco 2 is turned On, then it will
feed the base mix (PGM 1) and it
will be recorded. Likewise, if
Telco 1 is turned Off while
Telco 2 is Off, then the Base Mix
changes to Offline and Telco 2
will feed the left channel of the
Telco Record Output.
Recording Functions with Auto F/B
Off on all To Record Telcos