Harman Martin MAC Aura XIP User Manual Download Page 15

Page: 15 / 94

Control options

Supported RDM PIDs

The fixture supports the standard RDM PIDs (Parameter IDs) required by ESTA plus manufacturer-specific
PIDs that give a range of configuration options.

See the following tables.

Standard RDM Parameter IDs

GET

allowed

SET

allowed

RDM parameter IDs

Notes

Network Management

DISC_UNIQUE_BRANCH

DISC_MUTE

DISC_UN_MUTE

Status Collection



QUEUED_MESSAGE



STATUS_MESSAGES



STATUS_ID_DESCRIPTION



CLEAR_STATUS_ID

RDM Information



SUPPORTED_PARAMETERS



PARAMETER_DESCRIPTION

Product information



DEVICE_INFO



DEVICE_MODEL_DESCRIPTION



MANUFACTURER_LABEL



DEVICE_LABEL



FACTORY_DEFAULTS



SOFTWARE_VERSION_LABEL

DMX Setup



DMX_PERSONALITY



DMX_PERSONALITY_DESCRIPTION



DMX_START_ADDRESS



SLOT DESCRIPTION

Sensors



SENSOR_DEFINITION



SENSOR_VALUE

Usage information



DEVICE_HOURS



DEVICE_POWER_CYCLES

Display settings



DISPLAY_INVERT



DISPLAY_LEVEL

Configuration



PAN_INVERT



TILT_INVERT

Network configuration



LIST_INTERFACES



INTERFACE_LABEL



INTERFACE_HARDWARE_ADDRESS_
TYPE1



IPV4_DHCP_MODE

Summary of Contents for Martin MAC Aura XIP































































































Search results

Summary of Contents for Martin MAC Aura XIP

Reviews:

Related manuals for Martin MAC Aura XIP

Brands by name

Popular brands

Harman Martin MAC Aura XIP, User Manual

Search results

Summary of Contents for Martin MAC Aura XIP

Reviews:

Related manuals for Martin MAC Aura XIP

Brands by name

Popular brands