9
REAR PANEL CONNECTIONS
Rear Panel Connections
THIS PRODUCT COMPLIES WITH APPLICABLE
REQUIREMENT OF THE DHHS PERFORMANCE
STANDARD FOR LASER PRODUCTS,
21 CFR SUBCHAPTER J.
DHHS CODE : GV
WARNING :
SHOCK HAZARD-DO NOT OPEN!
AVERTISSEMENT :
RISQUE DE CHOC ELECTRIQUE-NE
PAS OUVRIR!
CLASS 1 LASER PRODUCT
KLASSE 1
LASER PRODUKT
LUOKAN 1 LASER LAITE
KLASS 1
LASER APPARAT
CLASSE 1
PRODUIT
LASER
RISK OF ELECTRIC SHOCK.
DO NOT OPEN.
CAUTION
CAUTION
VISIBLE AND INVISIBLE LASER
RADIATION WHEN OPEN.
DO NOT STARE INTO BEAM OR
VIEW DIRECTLY WITH OPTICAL
INSTRUMENTS.
MODEL NO. DVD 50
harman / kardon
NORTHRIDGE
CALIFORNIA 91329, USA
MADE IN KOREA
Manufactured/Date De Fab.:
Serial No./No. De Series
"DTS" and "DTS Digital Out" are trademarks of
Digital Theater Systems, Inc.
Appartus Claims of U.S. Patent Nos. 4,631,603,
4,577,216, 4,819,098, and 4,907,093 licensed
for limited viewing uses only.
AC INPUT
100-240VAC 50/60Hz 18W
VIDEO OUT
DIGITAL OUT
AUDIO OUT
S-VIDEO
PROGRESSIVE/COMPONENT
SCAN VIDEO
OPTICAL
COAXIAL
Pr
Pb
Y
COMPOSITE
R
L
REMOTE
CONTROL
OUT
IN
¡ ™
£
¢ ∞
ª
•
¶
§
Manufactured under license from Dolby Laboratories.
"Dolby" ,"Pro Logic", and the double-D symbol
are trademarks of Dolby Laboratories.
Confidential unpublished works.
Copyright 1992-1997 Dolby Laboratories.
All rights reserved.
¡
Remote Control Input
™
Remote Control Output
£
Analog Audio Outputs
¢
Component Video Outputs
∞
Composite Video Output
§
S-Video Output
¶
Coaxial Digital Output
•
Optical Digital Output
ª
AC Power Cord
¡
Remote Control Input:
Connect the
output of a remote infrared sensor, or the
remote control output of another compatible
Harman Kardon product, to this jack. This will
enable the remote control to operate even
when the front panel
Remote Sensor
^
is
blocked. This jack may also be used with com-
patible IR remote control-based automation
systems.
™
Remote Control Output:
Connect this
jack to the infrared (IR) input jack of another
compatible Harman Kardon remote-controlled
product to have the built-in
Remote Sensor
^
on the DVD 50 provide IR signals to other
compatible products.
£
Analog Audio Outputs:
Connect these
jacks to an audio input on an A/V receiver or
surround processor for analog audio playback.
¢
Component Video Outputs:
These out-
puts carry the component video signals for con-
nection to analog or digital display monitors
with component video inputs. For standard
analog TVs or projectors with inputs marked
Y/Pr/Pb or Y/Cr/Cb, connect these outputs to
the matching inputs. If you have a digital televi-
sion that is compatible with high scan rate
video, connect these jacks to the “HD
Component” inputs. note that a change must
be made to the setup menus in order to take
advantage of the progressive scan circuitry. See
page 22 for more information on progressive
scan video. Note that these jacks should NOT
be connected to standard composite video
inputs.
∞
Composite Video Output:
Connect this
jack to the video input on a television or video
projector, or to a video input on an A/V receiver
or processor if you are using that type of device
for video input switching.
§
S-Video Output:
Connect this jack to the
S-Video input on a television or video projector,
or to an S-Video input on an A/V receiver or
processor if you are using that type of device
for S-Video input switching.
¶
Coaxial Digital Output:
Connect this jack
to the coaxial digital input of an A/V receiver or
surround processor for Dolby Digital, DTS or
PCM audio playback.
NOTE:
The coaxial digital output should only be
connected to a digital input. Even though it is
the same RCA-type connector as standard ana-
log audio connections, DO NOT connect it to a
conventional analog input jack.
•
Optical Digital Output:
Connect this jack
to the optical digital input of an A/V receiver or
surround processor for Dolby Digital, DTS or
PCM audio playback.
ª
AC Power Cord:
Connect this plug to an
AC outlet. If the outlet is controlled by a switch,
make certain that it is in the ON position.
