Hardt Elemendt 1000 Operation Manual Download Page 29 | Manualshive

Page: 29 / 32

background image

HARDT

Responsive, Reliable Solutions

29 of 32

C

U

S

-0

1

3

-0

0

0

1

-0

9

7. Troubleshooting

Troubleshooting

SERVICE/REPAIRS SHOULD ONLY BE PERFORMED BY TRAINED PERSONNEL.

DISCONNECT POWER TO THE ROTISSERIE BEFORE ANY MAINTENANCE, SERVICE OR
CLEANING IS PERFORMED.

THE ROTISSERIE IS HOT WHEN OPERATING. EXERCISE CAUTION WHEN WORKING NEAR
THE HOT ROTISSERIE.

WEAR APPROPRIATE PROTECTIVE CLOTHING BEFORE ANY MAINTENANCE, SERVICE OR
CLEANING IS PERFORMED.

7.1

Numeric Temperature Display Mode Change

If it is required to have the temperature display mode switched from Fahrenheit to Celsius or vice versa,
contact your local authorized service partner.

7.2

Equipment Fails to Operate

The rotisserie does not operate when the red main ON/OFF switch is pulled out (i.e. drive does not turn, and
no lights in cavity).

Solution

1. Verify that the front and rear doors (depending on your model) are fully closed. The magnetic

door switches disables or enables the electrical system.

2. Check rotisserie electrical power: If the rotisserie's lights are off, ensure that the power cord is

plugged into the wall and that there is power coming from the wall outlet. If power is available
and the rotisserie still does not operate, contact your local authorized service partner.

«
...
27
28
29
30
31
...
»

Summary of Contents for Elemendt 1000

































Reviews:

No comments

Related manuals for Elemendt 1000

Brand: OMCA Pages: 72

Brand: B&K Pages: 5

Brand: GE Pages: 43

Brand: GE Pages: 37

Brand: GE Pages: 210

Brand: GE Pages: 160

Brand: GE Pages: 146

Brand: GE Pages: 6

Brand: GE Pages: 27

Brand: GE Pages: 4

Brand: Cadman Pages: 66

Brand: Raymarine Pages: 90

Brand: Zenbooth Pages: 60

Brand: Keiser Pages: 82

Brand: Keiser Pages: 4

Brand: JBL Pages: 38

Brand: GE Pages: 194

Brand: Warner Electric Pages: 14

Brands by name

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Popular brands

Load more brands