Haldex EB+ Gen3 Installation Manual Download Page 47

Page: 47 / 132

EB+ Gen3

Installation guide

2013

Innovative Vehicle Solutions

Piping information

›

Actual pipe sizes need to be optimized for individual trailer response time requirements

›

All pipe and rubber hose to comply to recognized international standards

›

Nylon pipe to DIN 73378, rubber hose to SAE 1402

›

The referenced sizes are deﬁned as guide lines only

›

For optimum performance all pipe lengths should be as short as possible

Pipe fittings

Avoid elbows as much as possible. If essential, use
swept type elbow.

Inside diameter of ﬁtting should be the same as the
inside pipe diameter it is serving.

On metric (parallel thread) pipe ﬁtting a backing
washer and ‘O’ ring should be used.

The use of tape (PTFE) must not be used.

Note:
No pipe sealant or tape (PTFE) must be used during the
installation of EB+ Gen3. No warranty claims will be
accepted on pipe sealant or tape induced faults.

Summary of Contents for EB+ Gen3





































































































































Search results

Summary of Contents for EB+ Gen3

Reviews:

Related manuals for EB+ Gen3

Brands by name

Popular brands

Haldex EB+ Gen3, Installation Manual

Search results

Summary of Contents for EB+ Gen3

Reviews:

Related manuals for EB+ Gen3

Brands by name

Popular brands