Haldex EB+ Gen3 Installation Manual Download Page 45

Page: 45 / 132

EB+ Gen3

Installation guide

2013

Innovative Vehicle Solutions

Ø 24 MAX

Ø 50 MAX

40.0

MIN

40.0

MIN

300 MAX

100

MIN

Alt

120.0

MIN

65.0

MIN

‘DIAG‘ side of vehicle connection

Clearance and mounting dimensions

Shaded area around hole to be ﬂat and free from
raised markings or surface imperfections which may
prevent ﬂush ﬁtting of the connector.

Mount the diagnostic connector on the outside of the
main chassis rail. The position must be in an accessible
area but not in the direct spray of the wheels.

The connector must be mounted horizontally.

Tighten nut ‘R’ to a torque of 3-4 Nm (2-3 Ibft).

ECU connection is as right.

Cable to run up to connector and secured to the
chassis, or appropriate cable or pipe runs, with cable
ties at 300 mm maximum intervals.

Ensure that the cover is ﬁtted and correctly ‘locked’ in
place.

Note:
For Installation of Info Center refer to Instructions
006 300 000.

Diagnostic ‘DIAG’ - side of vehicle connection - option 3

min

max

Summary of Contents for EB+ Gen3





































































































































Search results

Summary of Contents for EB+ Gen3

Reviews:

Related manuals for EB+ Gen3

Brands by name

Popular brands

Haldex EB+ Gen3, Installation Manual

Search results

Summary of Contents for EB+ Gen3

Reviews:

Related manuals for EB+ Gen3

Brands by name

Popular brands