Haldex EB+ Gen3 Installation Manual Download Page 102 | Manualshive

Page: 102 / 132

background image

EB+ Gen3

Installation guide

102

Innovative Vehicle Solutions

2013

The EB+ Gen3 system has two power up modes to aid in system testing. With switching the Ignition ‘On’
(B+ applied) the following occurs:

With no yellow line pneumatic pressure (i.e. brakes ‘Off’).
The system adopts load sensing mode when the brakes are applied. This load sensing mode is limited to 2
minutes for any single brake application, after which it returns to a push-through condition (approx 1:1).

The push-through condition is cancelled on vehicle movement above 10 km / h returning the system to load
sensing operation.

With yellow line pneumatic pressure (i.e. Brakes ‘On’, park on air).
Apply foot brake, switch Ignition ‘On’.
The system adopts a push-through (approx 1:1) condition. When the brakes are released and re-applied the
system remains in push-through unless the brakes are released for longer than 2 minutes, after which it returns to
load sensing operation.

This condition is cancelled on vehicle movement above 10 km / h returning the system to load sensing operation.

Power up modes

«
...
100
101
102
103
104
...
»

Summary of Contents for EB+ Gen3





































































































































Reviews:

No comments

Related manuals for EB+ Gen3

Brand: Nacon Pages: 12

Brand: SALSA Pages: 2

BEA LZR-WIDESCAN

Brand: Halma Pages: 12

Brand: Panasonic Pages: 18

Brand: Jabra Pages: 2

Brand: Fenix Pages: 4

Brand: Panasonic Pages: 72

AS5000 - Transcription Kit - Digital Voice...

Brand: Olympus Pages: 17

Brand: Rice Lake Pages: 2

Brand: Yoshimura Pages: 7

Brand: Pitney Bowes Pages: 22

Brand: R&G Pages: 22

Brand: R&G Pages: 8

Elpro Large electrol

Brand: Projecta Pages: 2

Brand: Toyota Pages: 371

Brand: Tobii Pro Pages: 34

Brand: IBASE Technology Pages: 100

Brand: JUGS Pages: 17

Brands by name

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Popular brands

Load more brands