Haldex EB+ Gen3 Installation Manual Download Page 39

Page: 39 / 132

EB+ Gen3

Installation guide

2013

Innovative Vehicle Solutions

3 º

Within LH & RH
chassis members

Rear view

Plan View

5 º

Single or Tri-axle

Within LH & RH
chassis members

Tandem axle

Trailer

Semi

1.5 m

Centre-axle

1.5 m

Full

3.0 m

1.5 m

Chassis installation

The following installation parameters are required for
correct stability operation.

Roll angle : ± 3 ° (1:20)

Yaw angle : ± 5 °

The EB+ Gen3 system is to be mounted within distance
X & Y from the centre line of the rear axle group / bogie
(includes lift axles).

The EB+ Gen3 assembly to be within the main left hand
(LH) and right hand (RH) chassis members of the vehicle.

For any other applications please refer to Haldex
Technical Services.

Pitch angle: assembly must be mounted vertically.

The assembly should not be in direct spray or splash
water area and should be protected against high
pressure cleaning.

Haldex recommended position for maximum stability
performance. Fitment of EB+ Gen3 outside of this area
may affect the stability performance.

This way up

Position of EB+ Gen3 assembly

Summary of Contents for EB+ Gen3





































































































































Search results

Summary of Contents for EB+ Gen3

Reviews:

Related manuals for EB+ Gen3

Brands by name

Popular brands

Haldex EB+ Gen3, Installation Manual

Search results

Summary of Contents for EB+ Gen3

Reviews:

Related manuals for EB+ Gen3

Brands by name

Popular brands