Hainbuch HYDROK Installation Manual Download Page 83

Page: 83 / 100

HYDROK – Maintenance

8.2 Cleaning

4. x

NOTE!
Material damage if cleaned with com-
pressed air!

Cleaning the clamping device with compressed
air can force metal chips into thread and
grooves. This can damage or even destroy the
clamping device.



Never clean the clamping device with com-
pressed air!



Auxiliary material required:



Ester-free, non-polar cleaning agent



Soft, lint-free cloth

CAUTION!
Damage of the seal rings when partial dis-
assembly!

When partly disassembling of the stationary
chuck for cleaning / service, the seal rings will
be damaged!

Keep a new set of seal rings ready for re-
assembling.

Fig. 32

1. Disassembled the clamping device [see chapter

»Disassembling the clamping device«].

CAUTION!
Risk of injury due to spring tension!

While disassembling the stationary chuck for
cleaning / preservation, the clamping device
may cause severe injuries.



The partly disassembly may only be done by
HAINBUCH service personnel.

2. Clean all the components listed below with clean-

ing agent and a cloth; remove all oil and grease
residues:



Taper reception



coupling area

Order h49 7144.907-333

Summary of Contents for HYDROK





































































































Search results

Summary of Contents for HYDROK

Reviews:

Related manuals for HYDROK

Brands by name

Popular brands

Hainbuch HYDROK, Installation Manual

Search results

Summary of Contents for HYDROK

Reviews:

Related manuals for HYDROK

Brands by name

Popular brands