manualshive.com logo in svg

H3C MSR Router Comware 5 Series, Manual

Share
Download
H3C MSR Router Comware 5 Series Manual Download Page 74

 

65 

Item MIM-1CPOS(E)/MIM-1CPOS(T) 

Interface standard

 

SONET OC-3/SDH STM-1 

Interface rate

 

155.52 Mbps 

 

 

IMPORTANT: 

If the interface receives signal over a long-haul optical fiber, make sure the transmission distance is 
longer than 25 km (15.53 miles). If the transmission distance is shorter than 25 km (15.53 miles), use 
an optical attenuator to reduce the optical power. 

 

Interface LEDs 

Figure 69 MIM-1CPOS(E) front panel 

 

 

Figure 70 MIM-1CPOS(T) front panel 

 

 

Table 90 LED description 

LED Description 

LINK 

•

 

Off: No link is present. 

•

 

On: A link is present.

 

ACT 

•

 

Off: No data is being transmitted or received. 

•

 

Flashing: Data is being received or transmitted. 

 

 

Transceiver modules, optical fibers, and connection methods 

For more information about transceiver modules, optical fibers, and the connection methods, see 
"

Fiber port

."

 

E1/T1 interface module 

•

 

MIM-1E1 

•

 

MIM-2E1 

•

 

MIM-4E1 

•

 

MIM-1E1-F 

•

 

MIM-2E1-F 

•

 

MIM-4E1-F 

•

 

MIM-8E1 

Summary of Contents for MSR Router Comware 5 Series




























































































































































































































Reviews:

No comments

Brands by name

Popular brands

Load more brands