manualshive.com logo in svg

H3C MSR Router Comware 5 Series, Manual

Share
Download
H3C MSR Router Comware 5 Series Manual Download Page 148

 

139 

3. 

Run the 

display version

 command to display the driver version. If the version number is 

changed, the upgrade is completed. 

The driver version number is just like (Driver) 1.0 in the module information displayed as 
follows:  

[SLOT  5]MIM-6FCM       (Hardware)1.0,   (Driver)1.0,    (Cpld)1.0 

Voice interface module 

•

 

FIC-2FXS 

•

 

FIC-2FXO 

•

 

FIC-4FXS 

•

 

FIC-4FXO 

•

 

FIC-2E&M 

•

 

FIC-4E&M 

•

 

FIC-24FXS 

•

 

DFIC-24FXO24FXS 

•

 

FIC-2BSV 

•

 

FIC-4BSV 

•

 

FIC-2VE1 

•

 

FIC-2VT1 

•

 

FIC-1VE1 

•

 

FIC-1VT1 

FIC-2FXS/FIC-2FXO/FIC-4FXS/FIC-4FXO 

Introduction 

The 2-/4-port voice subscriber circuit interface module (FIC-2FXS/FIC-4FXS) processes and 
transmits over data communications networks voice signals for 2/4 regular analog phones, faxes, or 
AT0 loop trunks of telephone exchanges.  

The 2-/4-port voice AT0 analog trunk interface module (FIC-2FXO/FIC-4FXO) processes and 
transmits over data communications networks voice signals for 2/4 loops of telephone exchanges. 

Interface specifications 

Table 187 Interface specifications 

Item Description 

Connector

 

RJ-45 

Number of connectors

 

•

 2 

(FIC-2FXS/FIC-2FXO) 

•

 4 

(FIC-4FXS/FIC-4FXO)

 

Summary of Contents for MSR Router Comware 5 Series




























































































































































































































Reviews:

No comments

Brands by name

Popular brands

Load more brands