manualshive.com logo in svg

H3C MSR Router Comware 5 Series, Manual

Share
Download
H3C MSR Router Comware 5 Series Manual Download Page 118

 

109 

Interface LEDs 

Figure 122 FIC-1AE3 panel 

 

 

Table 151 LED description 

LED Description 

LINK/ACT 

•

 

On: Carrier signal has been received. 

•

 

Flashing: Data is being received or/and transmitted. 

•

 

Off: No carrier signal has been received. 

LP/AL 

•

 

On: The interface is in a loopback.  

•

 

Off: No loopback or alarm is present.  

•

 

Flashing: An alarm indication signal (AIS), loss of frame alignment (LFA) 
signal, or remote alarm indication (RAI) signal is present.  

 

Interface cables and the connection methods 

For more information about E3 interface cables and the connection methods, see "

E3/T3 interface

." 

FIC-1AT3 

Introduction 

The 1-port 44 Mbps ATM-T3 interface module (FIC-1AT3) provides these functions: 

•

 

Two ATM cell mapping modes: ADM and PLCP 

•

 

Scrambling in data transmission 

•

 

Line clock (when working as DTE interface) and internal clock (when working as DCE interface) 

•

 

Four types of test measures: local cell loopback, local loopback, remote payload loopback, and 
remote line loopback 

Interface specifications 

Table 152 Interface specifications 

Item Description 

Connector SMB 

Number of connectors  

2 

Interface standard 

G.703, G.704, G.823 

Interface rate 

44.736 Mbps 

Summary of Contents for MSR Router Comware 5 Series




























































































































































































































Reviews:

No comments

Brands by name

Popular brands

Load more brands