manualshive.com logo in svg

H3C MSR Router Comware 5 Series, Manual

Share
Download
H3C MSR Router Comware 5 Series Manual Download Page 112

 

103 

FIC-1GBE/FIC-2GBE 

Introduction 

The 1-port/2-port 10Base-T/100Base-TX/1000Base-T Ethernet copper port module 
(FIC-1GBE/FIC-2GBE) is used for router-to-LAN communication. 

The modules support: 

•

 

100 m (328.08 ft) of transmission segment over the category-5 twisted-pair cable 

•

 

Operation at 1000 Mbps, 100 Mbps, and 10 Mbps, autosensing 

•

 

Half-duplex/full duplex, autosensing 

Interface specifications 

The following table describes the interface specifications for the FIC-1GBE/FIC-2GBE: 

Table 142 Interface specifications 

Item FIC-1GBE 

FIC-2GBE 

Connector RJ-45 

Number of connectors 

1 

2 

Interface type 

MDI/MDIX 

Interface standard 

802.3, 802.3u, and 802.3ab 

Cable type 

Ethernet cable 

Operating mode 

10/100/1000 Mbps autosensing 
Half-duplex/full duplex, autosensing 

 

Interface LEDs 

Figure 114 FIC-1GBE panel 

 

 

Figure 115 FIC-2GBE panel 

 

 

Summary of Contents for MSR Router Comware 5 Series




























































































































































































































Reviews:

No comments

Brands by name

Popular brands

Load more brands