manualshive.com logo in svg

H3C MSR Router Comware 5 Series, Manual

Share
Download
H3C MSR Router Comware 5 Series Manual Download Page 114

 

105 

Figure 117 FIC-2GEF panel 

 

 

Table 145 LED description 

LED Description 

LINK 

•

 

Off: No link is present. 

•

 

On: A link is present.

 

ACT 

•

 

Off: No data is being transmitted or received. 

•

 

Flashing: Data is being received or/and transmitted. 

 

 

Transceiver modules, optical fibers, and connection methods 

For more information about transceiver modules, optical fibers, and the connection methods, see 
"

Fiber port

." 

ATM interface module 

•

 

FIC-IMA-4E1 

•

 

FIC-IMA-8E1 

•

 

FIC-IMA-4T1 

•

 

FIC-IMA-8T1 

•

 

FIC-1AE3 

•

 

FIC-1AT3 

•

 

FIC-1ATM-OC3 

FIC-IMA-4E1/FIC-IMA-8E1 

Introduction 

The 4-port/8-port E1 ATM inverse multiplexing interface module (FIC-IMA-4E1/FIC-IMA-8E1) 
provides four/eight E1 interfaces that support the IMA (inverse multiplexing for ATM) technology.  

The IMA technology combines multiple low-speed links into a group to support a high-speed ATM 
cell stream: It distributes an ATM cell stream over multiple low-speed E1 links on cell by cell basis at 
the transmission end and reassembles the cells on the low-speed E1 links into the original stream at 
the far end. This technology provides a scalable and cost-effective solution, and is commonly used in 
PDH networks to transport ATM cells. 

Summary of Contents for MSR Router Comware 5 Series




























































































































































































































Reviews:

No comments

Brands by name

Popular brands

Load more brands