manualshive.com logo in svg

H3C MSR Router Comware 5 Series, Manual

Share
Download
H3C MSR Router Comware 5 Series Manual Download Page 20

 

11 

Interface specifications 

Table 16 Interface specifications 

Item

 

Description

 

Connector type

 

D15

 

Number of connectors

 

1 

Interface standard

 

•

 G.703 

•

 G.704

 

Interface rate

 

2.048 Mbps

 

Cable type

 

•

 

75-ohm unbalanced coaxial cable (D15 to BNC) 

•

 

Coaxial connector, network interface connector, and 75-ohm to 120-ohm 
adapter 

NOTE: 

The default resister for the interface on the SIC-1EPRI is 75 ohm. A 75-ohm to 
120-ohm adapter must be used when a 120-ohm cable is connected to the 
SIC-1EPRI.

 

Operating mode

 

•

 E1 

•

 CE1 

•

 ISDN 

PRI 

Supported service

 

•

 Backup 

•

 Terminal 

access 

•

 ISDN 

 

Interface LEDs 

Figure 12 SIC-1EPRI panel 

 

 

Table 17 LED description 

LED Description 

LINK/ACT 

•

 

On: Carrier signals are received. 

•

 

Flashing: Data is being transmitted or received. 

•

 

Off: No carrier signals are received.  

LP/AL 

•

 

On: The interface is in a loopback. 

•

 

Flashing: An alarm indication signal (AIS), loss of frame alignment (LFA) 
signal, or remote alarm indication (RAI) signal is present. 

•

 

Off: Neither loopback nor alarm is present. 

 

Interface cables and the connection methods 

For more information about E1 interface cables and the connection methods, see "

E1 interface

." 

Summary of Contents for MSR Router Comware 5 Series




























































































































































































































Reviews:

No comments

Brands by name

Popular brands

Load more brands