manualshive.com logo in svg

H3C MSR Router Comware 5 Series, Manual

Share
Download
H3C MSR Router Comware 5 Series Manual Download Page 180

 

171 

Connecting a 4-port E1 75-ohm cable (D25 <----> D15)  

1. 

Connect the D25 connector of the 4-port E1 75-ohm cable to the D25 interface of the interface 
module and fasten the bolts to fix the cable. 

2. 

The other end of the cable provides four D15 connectors. Connect them to the D15 interfaces 
on the remote device as needed. 

Figure 176 Connect an 4-port E1 75-ohm cable 

 

 

Connecting a 1-port E1 120-ohm cable (D15 <----> RJ-45) 

1. 

Connect the D15 connector of the E1 120-ohm cable to the D15 interface on the interface 
module and fasten the bolts to fix the cable. 

2. 

The other end of the cable provides one or multiple RJ-45 connectors. Connect them to the 
RJ-45 interface on the remote device as needed.  

Figure 177 Connecting an E1 120-ohm cable 

 

 

Connecting a 4-port E1 120-ohm cable (D25 <----> D15) 

1. 

Connect the D25 connector of the 4-port E1 120-ohm cable to the D25 interface on the interface 
module and fasten the bolts to fix the cable. 

2. 

The other end of the cable provides four D15 connectors. Connect them to the D15 interface on 
the remote device as needed. 

Device

(75ohm E1 Port)

1-port E1 75-ohm cable

TX

RX

TX

RX

E1 / E1-F
(75ohm)

4-port E1 75-ohm cable

……

Summary of Contents for MSR Router Comware 5 Series




























































































































































































































Reviews:

No comments

Brands by name

Popular brands

Load more brands