manualshive.com logo in svg

H3C MSR Router Comware 5 Series, Manual

Share
Download
H3C MSR Router Comware 5 Series Manual Download Page 144

 

135 

POS terminal access interface module 

•

 

FIC-6FCM 

•

 

FIC-1E1POS 

FIC-6FCM 

Introduction 

The 6-port fast connect modem interface module (FIC-6FCM) provides services for point of sale 
(POS) terminal devices to fast dial up to a bank card accounting system.  

 

 

NOTE: 

The point of sale (POS) access service refers to a type of smart card service widely used in places 
such as shopping malls and gasoline service stations. It links a POS terminal device located in a 
shopping mall or a gasoline service station to a bank card accounting system to provide services.

 

Interface specifications 

Table 183 Interface specifications 

Item Description 

Connector RJ-45 

Number of connectors 

6 

Cable 

Telephone cable with ferrite core 

Supported protocols 

ITU-T V.22 (PSK/QPSK) and V.22BIS (QAM) 

 

Interface LEDs 

Figure 153 FIC-6FCM panel 

 

 

Table 184 LED description 

LED Description 

CD 

•

 

Off: No carrier signals are detected.  

•

 

On: A carrier signal is detected.

 

ACT 

•

 

Flashing: Data is being received or transmitted. 

•

 

Off: No data is being received or transmitted. 

 

Summary of Contents for MSR Router Comware 5 Series




























































































































































































































Reviews:

No comments

Brands by name

Popular brands

Load more brands