manualshive.com logo in svg

H3C MSR Router Comware 5 Series, Manual

Share
Download
H3C MSR Router Comware 5 Series Manual Download Page 22

 

13 

Interface LEDs 

Figure 13 SIC-TPRI panel 

 

 

Figure 14 SIC-T1-F panel 

 

 

Table 19 LED description 

LED Description 

LINK/ACT 

•

 

On: The carrier signal has been received. 

•

 

Off: No carrier signal has been received. 

•

 

Flashing: Data is being transmitted or/and received. 

LP/AL 

•

 

On: The interface is in a loopback. 

•

 

Off: No loopback or alarm is present. 

•

 

Flashing: An alarm indication signal (AIS), loss of frame alignment (LFA) 
signal, or remote alarm indication (RAI) signal is present.  

 

Interface cables and the connection methods 

For more information about T1 interface cables and the connection methods, see "

T1 interface

." 

Serial interface module 

•

 

SIC-8AS 

•

 

SIC-16AS 

•

 

SIC-1SAE 

•

 

SIC-2SAE 

•

 

SIC-4SAE 

SIC-8AS 

Introduction 

The 8-port asynchronous serial interface module (SIC-8AS) mainly transmits and processes 
asynchronous data streams. 

SIC-8AS has these features: 

Summary of Contents for MSR Router Comware 5 Series




























































































































































































































Reviews:

No comments

Brands by name

Popular brands

Load more brands