manualshive.com logo in svg

H3C MSR Router Comware 5 Series, Manual

Share
Download
H3C MSR Router Comware 5 Series Manual Download Page 166

 

157 

Interface LEDs 

There is no LED on the VCPM module and display of the status of the module is implemented 
through the VCPM interface LED on the main board of the router. 

The following table describes the LEDs on the main board: 

Table 213 LED description 

LED Description 

VCPMNo 

•

 

Green: The VCPM module is in the slot and is operating normally.  

•

 

Yellow: The VCPM module is in the slot but cannot be accessed by the router.

Note: 
"No" means the slot number VCPM module LED is on. 

 

Installing/removing a VCPM module 

For procedures of installing and removing a VCPM module, see the installation guide for the H3C 
MSR router series.. 

VPM 

Introduction 

The voice processing module (VPM) functions encoding/decoding, echo cancellation (EC) and 
comfortable noise generation (CNG) of voices. 

Interface specifications 

Table 214 Interface specifications 

Item Description 

Number of calls 
supported 

•

 8 

•

 16 

•

 24 

•

 32 

•

 128 

•

 256 

•

 512 

 

Installing/removing a VPM module 

For procedures of installing and removing a VPM module, see the installation guide for the H3C MSR 
router. 

Summary of Contents for MSR Router Comware 5 Series




























































































































































































































Reviews:

No comments

Brands by name

Popular brands

Load more brands