Güralp DM24 MkIII Operator'S Manual Download Page 82

Page: 82 / 130

Güralp DM24 Mk

Ⅲ

Command line interface

RE-SYNC ON

instructs the DM24 to resynchronize the real-time clock module to GPS

time when a GPS fix is next obtained.

RE-SYNC OFF

cancels a previous

RE-SYNC ON

instruction, so that attaching a GPS

module will no longer cause the DM24 to resynchronize.

6.10.8 ?LITHIUM

Note:

This command is only available in units with a precision real-time

clock module fitted.

Note:

This command is in the extended dictionary: to use it, first type

ok-1

and finish with

[seal]

Syntax:

?LITHIUM

Query the current status of the RTC's internal battery.

6.10.9 RE-BOOT

Syntax:

RE-BOOT

(interactive)

Causes the DM24 to reboot after a delay of 2 s.

RE-BOOT

Confirm with 'y' ?

Responding to the confirmation message with anything other than

will abort the

reboot.

6.11 Data storage and transmission

6.11.1 SHOW-FLASH

Syntax:

SHOW-FLASH

Reports status information about the Flash memory in the DM24, if fitted. For
example, the output from

SHOW-FLASH

for a new system with 8 × 64Mb chips fitted

would look like this:

512MB Flash File buffer : 16 Blocks Written 0 Unread
524,288 Free
Oldest data [16] Blank
Read point [16] Blank
Latest data [16] Blank
File Replay [16] Blank

For a system in use with 1 × 64Mb chip fitted, it might look like this:

MAN-D24-0004

Issue U - December, 2021

Summary of Contents for DM24 MkIII



































































































































Search results

Summary of Contents for DM24 MkIII

Reviews:

Related manuals for DM24 MkIII

Brands by name

Popular brands

Güralp DM24 MkIII, Operator'S Manual

Search results

Summary of Contents for DM24 MkIII

Reviews:

Related manuals for DM24 MkIII

Brands by name

Popular brands