Güralp DM24 MkIII Operator'S Manual Download Page 80

Page: 80 / 130

Command line interface

6.9.8 -AUTOCAL

Syntax:

-AUTOCAL

Cancels any automatic calibration setting in force. If automatic calibration is not
enabled, this command has no effect.

6.10 Actions

6.10.1 LOCK

Syntax:

LOCK

LOCK MONITOR

Locks the sensor mass(es) of the instrument connected to

SENSOR A

If you issue LOCK, the command returns immediately, allowing you to close the
terminal connection and follow the progress of the lock from the data streams.

If you issue

LOCK MONITOR

, the system displays the mass position for each

component, measuring one position each second (

i.e.

one reading every 4 seconds

for each component of a 4-component instrument). The process returns when
locking is complete.

The mass positions are measured to 16-bit accuracy, with full deflection
corresponding to values around ±32000 counts.

6.10.2 UNLOCK

Syntax:

UNLOCK

Unlocks the sensor mass(es) of the instrument connected to

SENSOR A

UNLOCK

returns immediately, whilst

UNLOCK MONITOR

monitors the progress of the

unlock by displaying mass positions, as for

LOCK MONITOR

(above).

6.10.3 CENTRE

Syntax:

CENTRE

CENTER MONITOR

Centres the sensor mass(es) of the instrument connected to

SENSOR A.

CENTRE

returns immediately, whilst

CENTRE MONITOR

monitors the progress of the

unlock by displaying mass positions, as for

LOCK MONITOR

(above).

When the masses are correctly centred, the mass positions should read less than
±1000 counts.

MAN-D24-0004

Issue U - December, 2021

Summary of Contents for DM24 MkIII



































































































































Search results

Summary of Contents for DM24 MkIII

Reviews:

Related manuals for DM24 MkIII

Brands by name

Popular brands

Güralp DM24 MkIII, Operator'S Manual

Search results

Summary of Contents for DM24 MkIII

Reviews:

Related manuals for DM24 MkIII

Brands by name

Popular brands