Güralp DM24 MkIII Operator'S Manual Download Page 97

Page: 97 / 130

Inside the DM24

The system is now reporting the current offset of the internal clock from GPS time
(whether slow or fast), and the current frequency error. It will now continuously
adjust the internal clock for as long as the GPS is powered up.

If you have chosen to save energy by enabling

GPS power cycling

, the DM24 will

switch off the GPS once a satisfactory fix is obtained, and begin free-running on the
internal clock. Whilst this is happening, the line will report

2005 8 10 17:06:27 GPS switched Off

7.1.1.4 Boot status

PLPGG SBHY00 CMG-3T

Boot Log : 143 Power cycles 294 Watchdog resets

Last boot 2006 1 12 16:18:57 2006 1 17 17:15:14

These three lines repeat information from the last re-boot:

•

in the first, the

System ID

, the

Stream ID

of the status stream, and the current

Sensor Type

;

•

in the second, the number of times the digitiser has been power cycled, and
the number of times it has been reset without power cycling (

e.g.

by a

re-

boot

after reconfiguring the module: a “soft” reset); and

•

in the third, the date and time of the last power cycle and of the last soft reset.

7.1.1.5 Environmental measurements

2006 1 18 14:56:15 External supply : 13.0V Temperature 24.68'C

The next line displays the current state of the DM24's power supply, and its internal
temperature.

7.1.1.6 Mass positions

2006 1 18 14:56:15 Mass positions -486 -300 -424

The final line provides the instantaneous mass positions reported by the sensor at
the time given.

7.1.2 Status blocks in continuous mode

In continuous mode, each status block contains a number of single-line messages:

2006 1 18 14:40:00 o/s= 90 drift= 0 pwm= 8187 Auto 3D

2006 1 18 14:41:00 o/s= 90 drift= 0 pwm= 8187 Auto 3D

2006 1 18 14:42:00 o/s= 90 drift= 0 pwm= 8187 Auto 3D

2006 1 18 14:43:00 o/s= 78 drift= -12 pwm= 8188 Auto 2D

2006 1 18 14:44:00 o/s= 89 drift= 11 pwm= 8188 Auto 3D

2006 1 18 14:45:00 o/s= 94 drift= 5 pwm= 8188 Auto 3D

2006 1 18 14:45:00 External supply : 13.0V Temperature 24.62'C

2006 1 18 14:46:00 o/s= 148 drift= 54 pwm= 8188 Auto 3D

2006 1 18 14:47:00 o/s= 174 drift= 26 pwm= 8188 Auto 3D

MAN-D24-0004

Issue U - December, 2021

Summary of Contents for DM24 MkIII



































































































































Search results

Summary of Contents for DM24 MkIII

Reviews:

Related manuals for DM24 MkIII

Brands by name

Popular brands

Güralp DM24 MkIII, Operator'S Manual

Search results

Summary of Contents for DM24 MkIII

Reviews:

Related manuals for DM24 MkIII

Brands by name

Popular brands