GSSI UtilityScan Page 24 Quick Start Manual Download | Manualshive

Page: 24 / 56

background image

UtilityScan Quick Start Guide

Page 18

•

Factory Reset:

Reset all settings to factory defaults.

•

Version Control:

View the current software user interface and antenna firmware versions.

You can also use this to update.

•

Select Language:

Use this to choose your desired language.

•

Units:

Toggle between English (Imperial) and Metric units.

•

Theme:

Toggle through the available user interface color schemes.

Once you have made your choices in the Carousel
Menu, tap Scan Setup on the left sidebar to transition to
the Scan Setup screen at the right.

The Menu Carousel will have the following options:

•

Depth:

Toggle through a list of preset values for

depth of investigation. These are approximate.
Exact depths are a function of soil conditions and
the dielectric constant you have specified.

•

Dielectric:

This will allow you to enter

in the assumed dielectric value of the material
through which you are scanning. A correct value
will result in an accurate time to depth calculation.
The UtilityScan will also use this value to calculate
the time range required to reach the specified depth.

Menu Carousel Softkeys

Color Table

Current
Depth
Setting

Back Button

«
...
22
23
24
25
26
...
»

Summary of Contents for UtilityScan

























































Reviews:

No comments

Related manuals for UtilityScan

Brand: JRC Pages: 316

Brand: Blaupunkt Pages: 28

Brand: Sangean Pages: 63

Brand: LightSquared Pages: 24

Brand: RELM Pages: 12

Brand: RELM Pages: 12

Brand: HIKOKI Pages: 44

Brand: Roadstar Pages: 2

Brand: Sailor Pages: 124

Brand: Kogan Pages: 17

Brand: dresden elektronik Pages: 36

Brand: Hama Pages: 61

Brand: Danita Pages: 48

Brand: RCA Pages: 4

Brand: Assan Pages: 24

Brand: Onix Pages: 28

NanoBeam 5AC Gen 2

Brand: Ubiquiti Pages: 28

Hendricks PFR-3B

Brand: QRPKits Pages: 20

Brands by name

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Popular brands

Load more brands