Gorilla Playsets Riverview Assembly Manual Download Page 79

Page: 79 / 94

Step 47: Picnic Table

1: Place the each 2 x 4 x 30” vertical pt supports 15” over from the corner posts. (see

rear view)
2: Make sure the vertical pt supports are square to the sandbox boards. Attach them

to the sandbox boards from the inside using two 2” wood screws. Attach the vertical pt

support (on front of the playset) to the 2 x 4 x 78” panel board using three 2-1/2” screws
3: Next find the 2 x 4 x 31 bench support board.
4 Attach the bench support board 17-7/8” up from the bottom edge of the sandbox

board. Use six 2-1/2” wood screws to attach the bench support board to the corner post

and the vertical pt support.

2 x 4 x 30”

Vertical PT Support

2-1/2”

Wood Screw

2 x 4 x 31”

Bench Support Board

Page 79

Summary of Contents for Riverview






























































































Search results

Summary of Contents for Riverview

Reviews:

Related manuals for Riverview

Brands by name

Popular brands

Gorilla Playsets Riverview, Assembly Manual

Search results

Summary of Contents for Riverview

Reviews:

Related manuals for Riverview

Brands by name

Popular brands