Gorilla Playsets Riverview Assembly Manual Download Page 94

Page: 94 / 94

WARRANTY REGISTRATION CARD

Go to

www.gorillaplaysets.com/category-s/112.htm

to fill out our online registration and save a stamp! If you

do not have internet access, fill out this form and return it to us to complete your registration.

Name: ___________________________________________________________________

Address: __________________________________________________________________

City, State, Zip: ____________________________________________________________

Email: ___________________________________________________________________

Date of Purchase: __________________________________________________________

Place of Purchase: __________________________________________________________

City, State, Zip: ____________________________________________________________

Please, check the boxes below.

Your age?

􀀗 18-25 􀀗 26-30 􀀗 31-35 􀀗 36-40 􀀗 41-45 􀀗 46-50 􀀗 51-55 􀀗 56-60

􀀗 61-65 􀀗 66+

How old are your children?

􀀗 2-3 􀀗 4-5 􀀗 6-7 􀀗 8+

How would you rate the quality of our product?

􀀗 Excellent 􀀗 Above average 􀀗 Average 􀀗 Below average 􀀗 Poor

Would you recommend this product?

􀀗 Yes 􀀗 No

Comments:

_________________________________________________________________________

Thank you for registering with Gorilla Playsets™! The information you provided will be kept

confidential and will ONLY be used to better serve our customers. Remove this page from the

manual and mail to the address below. Thank you from everyone here at Gorilla Playsets™!

Mail to:

Gorilla Playsets

190 Etowah Industrial Court

Canton, GA 30114

or fax: (678) 880-3329

Page 94

Summary of Contents for Riverview






























































































Search results

Summary of Contents for Riverview

Reviews:

Related manuals for Riverview

Brands by name

Popular brands

Gorilla Playsets Riverview, Assembly Manual

Search results

Summary of Contents for Riverview

Reviews:

Related manuals for Riverview

Brands by name

Popular brands